 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
| CUD928 |
|
| Metering Spring | |
| Quadrajet Varajet | |
| CUD158 |
|
| Accelerator Pump Spring 21/32 | |
| Quadrajet Varajet | |
| 66-37 |
|
| Fuel Filter Spring | |
| Quadrajet WCFB 4Jet R-2 Varajet R1 | |
| 64-344 |
|
| Accelerator Pump Cup Ethanol resistant | |
| 21/32 Quadrajet Varajet R1 - This is FLUORELASTOMER a special purpose fluorocarbon-based synthetic rubber. It has wide chemical resistance and superior performance, especially in high temperature . These are only resistant to a point | |
| 16-99 |
|
| MIXTURE SCREW (Pair) | |
| 10-32 x 1.75 - Quadrajet | |
| 16-98 |
|
| MIXTURE SCREW (pair) | |
| 10-32 x 1.78 - Quadrajet | |
| 80-7 |
|
| SCREWS x 10 | |
| Quadrajet WCFB butterfly | |
| 80-30 |
|
| Phillips Pan Head Screw 6-32 x 5/16 (qty 10) | |
| Bag of 10 Throttle shaft Screws | |
| 80-2 |
|
| Screw 3-48x1/4 Slot Pan Head x10 | |
| Bag of 10 Throttle shaft Screws | |
| TPS-1 |
|
| Throttle Position Sensor (New) | |
| Quadrajet / Dueljet | |
| 22-124 |
|
| Bushing 5/16 (pair) | |
| Knureled Brass - Fits 5/16th shafts (Primary) | |
| G622 |
|
| Throttle Rubber Grommet | |
| Quadrajet 4GC | |
| CU22-17 |
|
| Throttle Lever Bushing | |
| CUD976 |
|
| Fuel Inlet Fitting 1in x 20 Threads | |
| Quadrajet Varajet seal at bottom of threads - uses 3/8 fuel line 5/8 18 fitting | |
| CUD3914 |
|
| Brass Fuel Inlet Fitting 1in 20 threads Bottom Seal | |
| Quadrajet DuelJet Varajet - Seals bottom of threads - uses 3/8 fuel line 5/8 18 fitting | |
| CUD202 |
|
| Brass Fuel Inlet Fitting 1in 20 Threads | |
| Quadrajet - Seals at bottom of threads - uses 3/8 fuel line 5/8 18 fitting | |
| G816 |
|
| Gasket - Gas Filter Ring (x5) | |
| Quadrajet - Xtra thick Nylon for better sealing - These fit on the 1in 20 thread fittings 1972 and newer - ID - .795 OD - .935 | |
| CUD201 |
|
| Brass Fuel Inlet Fitting 7/8 threads x 5/8 18 | |
| Quadrajet - Seals bottom of Nut - uses 3/8 fuel Line | |
| CUD1280 |
|
| Brass Fuel Inlet Fitting - 7/8 threads x 5/8 18 | |
| ROCH. 2 & 4 BBL - Seals under nut - 3/8 fuel line | |
| G1126 |
|
| Gasket - GAS FILTER RING bag of 5 | |
| Quadrajet - Xtra thick Nylon for better sealing - These fit on the 7/8s thread fittings seals just under the nut - ID - .875 OD - 1.035 | |
| 251660c45 |
|
| 5/8 18 fitting 3/8 tube 50deg | |
| each - Fuel fitting 3/8 Inch Fuel line (5/8-18) Male Inverted Flare | |
| MCS-1 |
|
| Mixture Control Solenoid (NEW) - MCS Only | |
| LIMITED - Federal 81-90 Quadrajet Dualjet | |
| MCS-44 |
|
| NO LONGER AVAILIBLE - Rebuilt Mixture Control Solenoid M/C Dual Capacity PU with extra pigtail 85-87 | |
| Quadrajet - Must send in your rebuilable core first before we ship (no broken or burnt wires) | |
| G1032 |
|
| Gasket - Choke Ring | |
| Quadrajet R2 | |
| CUD2182 |
|
| Idle Mixture Screw Spring (EA) | |
| .590 Length | |
| CUD15044 |
|
| Choke Pulloff Rods | |
| Quadrajet choke connecting rod 2 5/8 tall | |
| CUD15043 |
|
| Choke Plate Rods | |
| Quadrajet choke connecting rod 2 1/2 in tall | |
| CUD1060 |
|
| Choke Plate Rods | |
| Quadrajet ref# 7035675 - 67-74 will work on 70-80 Quadrajet just has clip - about 3 in tall | |
| CUD3616 |
|
| Complete Acc. Pump Quadrajet 21/32 | |
| Ethanol resistant to a point Fits 90% of all quadrajets good universal replacement of some of the older designs - 2 5/8 inch tip to tip - 21/32 cup size | |
| CUD3614 |
|
| High Performance Complete Acc. Pump 21/32 | |
| Stronger Spring Ethanol resistant - 2 5/8 inch tip to tip | |
This Site Designed By
EH7.net
WebSite Design � 2008
